Furnace Replacement Cost in the GTA: Transparent Installed Prices
- For Saving
- 3 days ago
- 5 min read
Planning a furnace upgrade in the GTA? This quick 2025 guide explains realistic installed prices, the 10 factors that move your quote, and what a code-compliant install should include. Book a visit in Markham, Toronto, or anywhere in the GTA for a precise, line-item estimate.
The quick take (installed pricing in the GTA)
Most Greater Toronto homeowners invest about $4,000–$6,750+ installed for a high-efficiency gas furnace, depending on size, staging (single/two-stage/modulating), and site conditions.
Entry configurations with standard installation can start around $3,995; premium setups, complex installs, or top efficiency can run $7,500–$8,000+.
Your final number depends on equipment choice, duct condition, venting path, electrical/gas upgrades, permits, and labour.
Tip: Always compare written, line-item quotes so you know exactly what’s included.
GTA installed price ranges by scenario
Scenario | Typical Installed Range (CAD) | Why it lands here |
Entry high-efficiency (single-stage) | $3,995–$5,200 | Basic swap, minimal changes, smaller homes/condos; standard venting. |
Mid-tier (two-stage ECM) | $4,800–$6,750 | Quieter operation, better comfort/efficiency, moderate extras (new venting, minor electrical). |
Premium (modulating, highest AFUE) | $6,800–$8,500+ | Top comfort, advanced controls, tougher runs, tight spaces, add-ons. |
Fuel switch (e.g., oil/propane → gas) | $6,500–$10,000+ | New gas line/tank changes, venting, permits; broader scope can push costs higher. |
These are GTA-style ballparks for decision planning—your home and scope determine the final quote.
10 price factors every GTA homeowner should know
Capacity & sizing – Larger or leakier homes need more BTUs. A proper load calculation (Manual J style) prevents short-cycling and lowers lifetime costs.
Efficiency & staging – Single-stage is cheapest; two-stage and modulating raise upfront cost but improve comfort and can reduce gas usage.
Blower technology – ECM/DC blowers are quieter and more efficient than PSC but cost more.
Venting & location – Long or complex vent runs, roof penetrations, or relocating the furnace increases materials and labour.
Electrical & gas upgrades – New shutoffs, wiring, condensate pumps, or gas line work add scope; all must meet code.
Ductwork condition – Transitions, new returns, sealing, or static-pressure fixes improve comfort/airflow and may be required for warranty performance.
Thermostat & controls – Smart stats, communicating controls, or zoning add equipment and commissioning time.
Permits & inspections – Jurisdictional requirements are part of a compliant installation. Budget for them if not included.
Access & timing – Crawlspaces, cramped mechanical rooms, winter emergency swaps, or after-hours installs increase labour.
Add-ons – Humidifiers, HEPA/UV filtration, fresh-air intakes, and condensate lifts expand your quote.
Price by home size | Furnace Replacement Cost GTA
Home Type | Typical Furnace Size (BTU)* | furnace Installed Cost Tendencies |
Condo / Small Townhome | 40k–60k | Lower end of ranges if access/venting are straightforward. |
Semi-Detached / Mid-Size | 60k–80k | Middle of ranges; often two-stage ECM sweet spot. |
Large Detached / Older Leaky Homes | 80k–120k | Upper ranges; may benefit from duct improvements and modulating comfort. |
*Sizing must be verified by a professional heat-loss calculation; these values are planning ballparks only.
Markham & GTA specifics homeowners ask about
Do local permits or inspections impact costs?
They’re often included or itemized in professional quotes. If you see “standard installation,” confirm it covers required gas/electrical work, basic venting, disposal, and start-up. Any extras (e.g., long vent runs, condensate pumps, duct transitions) should be clearly line-itemed.
How long does a furnace install take?
A straightforward swap is commonly completed the same day. Add time for duct modifications, fuel changes, or tougher access.
Gas vs. electric vs. propane—what’s best here?
In the GTA, natural gas remains the most common for lifecycle cost and comfort. Electric can be cheaper to install but typically costs more to run in cold weather. Propane is viable where gas isn’t available but often has higher fuel costs.
Furnace installation Markham & across the GTA: what “good” looks like
When comparing Furnace installation Markham or Furnace installation GTA proposals, insist on:
Load calculation & duct check – Not just a like-for-like swap.
Clear scope – Model numbers, BTU size, staging, AFUE, blower type, accessories, venting path.
Code compliance – Licensed gas/electrical, permits, and TSSA-compliant practices.
Commissioning – Combustion analysis, temperature rise, static pressure, CO test, safety checks.
Warranty & aftercare – Parts, heat exchanger, and labour; what’s covered on future Furnace repairs GTA calls.
These steps separate a budget swap from a high-performing, code-compliant system that actually delivers comfort and efficiency.
Repair or replace? (The 40% rule of thumb)
If a major repair approaches ~40% of a new system and your furnace is older or out of warranty, replacement often pencils out better—especially before peak winter. Factor in energy savings, new warranty coverage, and the cost of repeat breakdowns.
Transparent quote checklist
Exact make/model, staging, AFUE, blower type
All-in price (equipment, labour, permits, disposal, thermostat, start-up)
Venting plan and any gas/electrical upgrades
Ductwork changes (transitions, returns, sealing, balancing)
IAQ add-ons (humidifier, filtration, UV) with separate pricing
Lead time and installation window; emergency options
Warranties (parts, heat exchanger, labour) and first-year tune-up plan
Financing, rentals, and total cost of ownership
Financing or rentals can soften upfront costs but compare total cost of ownership. A low monthly payment may hide higher long-term spend. Ask for both a cash price and a financed/rental comparison on the same quote.
Common add-ons (and when they’re worth it)
Two-stage or modulating heat – Smoother temperatures, less cycling; worth it if comfort is a priority or your home has temperature swings.
ECM blower – Quieter and more efficient; helps with filtration and airflow.
Humidifier – Valuable during GTA winters to protect wood floors and improve comfort.
High-MERV filtration / HEPA / UV – Consider if you have allergies, pets, or want cleaner indoor air.
Smart thermostat – Better scheduling, remote control, and energy tracking. Ensure compatibility with staging/modulating systems.
FAQ
How often should I service a new furnace?
Plan on annual maintenance to keep warranties valid, catch issues early, and maintain efficiency.
Can I reuse my old thermostat?
Often yes, but advanced systems can benefit from compatible smart/communicating controls for best performance.
Will a premium furnace actually lower my bills?
It can—especially with proper sizing, sealed ductwork, and smart controls. Comfort gains (quieter, steadier heat) are often the bigger day-to-day win.
How do I get a precise number for my home?
Book an in-home assessment. A tech will measure, inspect ducts/venting, review electrical/gas, and produce a line-item quote with good/better/best options.
Ready for a clear, GTA-specific quote?
Whether you’re in Markham, Toronto, Mississauga, or anywhere in the GTA, you can get a transparent, line-item estimate for Furnace installation Markham, Furnace installation GTA, or an honest assessment for Furnace repairs GTA if replacement isn’t the smartest move right now.
Pro tip: Ask every bidder to price good / better / best on a single proposal. It makes apples-to-apples comparisons easy—and prevents “mystery add-ons” later.
Primary: Get My Line-Item Quote
Alt: Book a Same-Day Assessment
Comments